My Junk

[JEEPISH]

How are all of you...

This is Josh (Black5) and my previous profile was not working correctly so I made a new one. I have been out of itsajeep for a while now. Here is my new junk...

http://lh6.ggpht.com/Blackcj5/SGF--SrjyzI/AAAAAAAAAr8/wO_wndJOVJY/jeep.jpg?imgmax=512

http://lh5.ggpht.com/Blackcj5/SGrT9857gZI/AAAAAAAAAx8/svCZpofUDYE/complete%20engine.jpg?imgmax=512

It is working well so far. I have been slowly transforming it from its previous state of disrepair to its current state.

My rig is

93 Jeep YJ

Current Parts
5.0 Interceptor motor
·MSD cap and rotor
·MSD coil
·Motocraft wires
·K & N filter
NP 435
205 t case
44HD high pinion
·New rebuild
·Lock right locker
14 bolt FF
Detroit locker
3” tach
TJ seats
Custom third bucket in back
Warn winch “needs Motor”
38.5 TSL's
203/205 doubler
Sky high steering arms
1.5” .25” wall tie rod and drag link with 7/8” heims
15 gal RCI Aluminum Fuel Cell
65mm BBK throttle body
Trail Gear Johny Joint shackle hangars

Incoming parts

Cherokee leaf springs front and rear "ordered" (will stretch wb to 108)
Rough country high travel shocks "ordered"


Wanted Parts

H1 beadlock rings
Roll cage
Racing seats
Drive shafts

I hope you all like it...

[BobA]

Nice rig!

[Matt'sXJ]

Nice, I like it.

[JEEPISH]

Thanks. It is going under the knife and getting completely reworked for about a month.

[JEEPISH]

By the way Simon at TORS does all the work on my Jeep. I need to post some pics of his fab skills so you all can see.

Here is the comp cut. We went flush with the top of the wheel wells so we stitch welded the body back together.

http://lh3.ggpht.com/Blackcj5/SJZbIbL_J6I/AAAAAAAAA0A/UbvMCEUXtvE/comp%20cut%201.jpg?imgmax=512

http://lh3.ggpht.com/Blackcj5/SJZbISnLbNI/AAAAAAAAA0I/JoZ2esbcBdw/comp%20cut%202.jpg?imgmax=512

[samb.]

more detailed pics of the comp cut if you can
like where he cut inside the fender and on the back cut as well please

what tool he use an air nibbler?

btw looks good i wish mine was finished

[JEEPISH]

He used a air powered body saw (I think that is what it was). I will get some better pics here soon as I will be starting a buildup thread. The only way we could have cut any more metal off would be to move the inner wheel well up:D

[Elven]

Looks good......also looks like and air reciprocating saw.....like a sawzall......? could be wrong...

[JEEPISH]

Yes like a mini air sawzall. Here is a pic from behind the jeep.

http://lh6.ggpht.com/Blackcj5/SJZuLjktUkI/AAAAAAAAA0Q/EqvCJ2Fd56c/comp%20cut%203.jpg?imgmax=512

As soon as I move the body mount I will cut it straight down where the line is.

[Don]

Nice rig. Sweet 5.0 you got there :cool: What exhaust do you have? There is nothing lke the sound of a V-8. :cool:

[JEEPISH]

The exhaust is nothing but bugger welds and rust with a decent muffler :) . It will be replaced shortly with a dynomax. Also the 5.0 is getting the boot in favor of a 5.8 351W.

[Fred]

I have heard this thing run and seen it in person....Don what is this exaust you speak of?

[JEEPISH]

Hey Fred... You don't belong here anymore, you got rid of your jeep.

[Ferrell's Jeep]

Frick! Dave's jeep is not going to have enough tire if your running 38.5 He only has 36s. We got to get him bigger tires.

Ferrell

[imhuntndeer]

Sweet 5.0 that's what I want mine to look like did you do the whole thing I like it a lot!!!!!!! Talked to kenny earlier today I'm going to look at his 5.0 conversion asap to get some mesurements and ideas would you mind if I did the same on yours again sweet jeep preston

[JEEPISH]

Thanks I appreciate it.

[Fred]

Hey Fred... You don't belong here anymore, you got rid of your jeep.
I still have a jeep. It is a grand Cherokee.....

[JEEPISH]

That is a Dodge Durango.:D